Panasonic activation key files - Free Download
Please read this manual carefully before using this product and save this manual for future use. In particular, be sure to read "1. System Components Category Model No. If a legacy gateway is connected to a KX-NS, the following equipment is also supported. Please consult your certified Panasonic dealer for more information.
The Structure of this Manual Table of Contents 8. Section 1 Safety Precautions This section provides important information intended to prevent personal injury and property damage.
The following symbols classify and describe the level of hazard and injury caused when this unit is operated or handled improperly. If the power cord or plug is damaged or frayed, contact an authorised Panasonic Factory Service Centre for a replacement. Otherwise, your programmed data will be cleared. To restart the PBX, refer to "7.
When the unit is installed in the new location, reconnect the power first, and then reconnect the telecom connection. Ensure that the AC outlet is located near the equipment and is easily accessible. Make sure that both connector cases frame ground of the RSC cross cable shielded cable are conductive. Contact your telephone company. A replacement fuse cover can be purchased from your local Panasonic dealer. Failure to do so may result in: Section 2 System Outline This section provides general information on the PBX, including the system capacity and specifications.
For an overview of One-look Networking Survivability, refer to "8. For details of One-look Networking Survivability, refer to "4. To be mounted on the mother board. Up to 2 legacy gateways can be connected. The maximum number of optional service card for legacy gateways is limited by the maximum number of extensions and trunks of the KX-NS Notice The capacities shown in these tables are for the largest possible configuration for each PBX i.
Connections that arrive over a stacking connection require the same amount of DSP resources as shown in this example. The maximum number of Air Sync Groups is The maximum number of Air Sync Groups is 8. For One-look network Terminal Equipment Type Section 3 Information about the Activation Keys This section provides information on activation keys, including how to obtain activation keys. Also, to upgrade the software to use enhanced features, the corresponding activation keys for that feature are required.
Bridge Allows the use of the Poltys Communication Bridge. Pkg 5 Users Allows the use of the following activation key features for 5 users: Preinstalled Activation Keys in the Mother Board Preinstalled activation keys for free trial The following activation keys are preinstalled on the mother board for the days free trial. They will expire 60 days after pressing the Activate Pre-installed Activation key button to begin the free trial. You can download the activation keys as an activation key file from the Key Management System.
Detailed instructions for planning the installation site, installing the main unit and optional service cards, and cabling of peripheral equipment are provided. Further information on peripheral equipment installation is included. Be sure to comply with all applicable laws, regulations, and guidelines. Notice Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
It is preferable not to install the system in the same room as the above equipment. Do not perform the following: Confirm that the power switch is turned off. Remove the support bar from the PBX. Then slide the top cover until it closes properly. Turn the screws clockwise to tighten. Screw Insert an earthing wire user-supplied. Earthing wire Connect the earthing wire to earth. Failure to do so may cause the PBX to malfunction due to static electricity.
Then, holding the card firmly in place, lower the rear end so that the holes of the card are aligned with the screw holes. Insert the screws into the holes on the card, and tighten the screws to secure the card. Screws Holding the rear end of the card, pull the card in the direction of the arrows. Some of the optional service cards require DIP switch settings which must be done before installing the card.
Screws Connect cables to appropriate ports of the card. For details about pin assignments, refer to the appropriate section in "4. For details about pin assignments, refer to "4. This procedure is described below. For details about Easy Setup Wizard, refer to "5. To prevent data leakage, render the Storage Memory Card physically unusable before disposal. Remove the Storage Memory Card installed in the slot on the mother board.
Insert the new Storage Memory Card into the slot on the mother board. Turn the screw clockwise to tighten. Dropping components may damage them or cause an injury. Install 4 anchor plugs in the wall and drive in 4 screws A leaving a gap of 5 mm between the screw head and the wall.
Installation procedure for concrete walls. If the arrows are not pointing upward, the PBX may fall, resulting in injury. The following illustrations are bad examples of wall mounting. Guide Hole Fully tighten all 4 screws A. Drive the screw to this point. Make sure to follow the instructions in this section. Overview A massive electrical surge can be caused if lightning strikes a telephone cable 10 m above ground, or if a telephone line comes into contact with a power line.
Terminal Board Surge Extn. Extension Line If you install an extension outside of the building, the following precautions are recommended: Install the extension wire underground. The earthing wire should be as short as possible. The earthing wire should run straight to the earth rod. For details about connecting peripherals, refer to "4. There is a risk of explosion if the battery is replaced with the incorrect type.
Doing so may result in damage to the PBX. Switch Settings Switch Type ON Synchronous Layer 2: Under m Installation Manual Cabinet Wall Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2 screws.
Screw To 4-pin terminal block Note While pressing on the orange tab at the bottom of the terminal block using a screwdriver, insert the wire into the upper hole as shown below.
If they are not conductive, make sure that both connector cases of the cable are firmly connected. The network parameters must be set for the IP telephone before it can be used. If PoE is available on your network, these IP telephones can receive the necessary power supply from the network through the network cable.
For details about backing up and restoring system data, refer to "6. This section describes programming basic items using Web Maintenance Console. A default IP address is assigned to each port. Note For details about connecting a switching hub to the PBX, refer to "4. It is not available from the Windows 8 Start screen.
In this case, log in to Web Maintenance Console again. This tool displays a "stacking style" image on the screen as necessary e. It will complete within one minute. For details about Easy Setup, refer to "5. For details about restarting the PBX, refer to "7. Conditions [Rules for data conversion] The following table shows the rules for converting system data to a different type.
Panasonic KX-NCP500 Installation Manual
Transmission delays can cause pauses and loss in VoIP communications. Screw Insert an earthing wire user-supplied. Preinstalled Activation Keys in the Mother Board Preinstalled activation keys for free trial The following activation keys are preinstalled on the mother board for the days free trial. Table Of Contents Connection In this case, log in to Web Maintenance Console again. Enter text from picture:
About extended function of V-Log L for DMC-GH4
Unplug this unit from the AC outlet if it emits smoke, an abnormal smell or makes unusual noise. If the arrows are not pointing upward, the PBX may fall, resulting in injury. Frame Earth Connection 4. Basic System Construction 1. Terminal Board Surge Extn. Confirm your input in Re-enter. Troubleshooting By Error Log 5. Cabinet Wall Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2 screws.
WJ-NV200 Activation Key Card
The following example shows the port number ranges set for each IP address Connection Of Extensions 3. Registering Ip Telephones 5. Remove the Storage Memory Card installed in the slot on the mother board. For details about Easy Setup Wizard, refer to "5. The network parameters must be set for the IP telephone before it can be used. Types Of Connectors 3. The number of simultaneous calls is proportional to number of extensions registered to the PBX, as shown in the chart below.